A new leak location method based on leakage acoustic waves for oil and gas pipelines

In order to study a new leak detection and location method for oil and natural gas pipelines based on acoustic waves, the propagation model is established and modified. Firstly, the propagation law in theory is obtained by analyzing the damping impact factors which cause the attenuation. Then, the dominant-energy frequency bands of leakage acoustic waves are obtained through experiments by wavelet transform analysis. Thirdly, the actual propagation model is modified by the correction factor based on the dominant-energy frequency bands. Then a new leak detection and location method is proposed based on the propagation law which is validated by the experiments for oil pipelines. Finally, the conclusions and the method are applied to the gas pipelines in experiments. The results indicate: the modified propagation model can be established by the experimental method; the new leak location method is effective and can be applied to both oil and gas pipelines and it has advantages over the traditional location method based on the velocity and the time difference. Conclusions can be drawn that the new leak detection and location method can effectively and accurately detect and locate the leakages in oil and natural gas pipelines.     

300MW锅炉低NOx燃烧系统改造效果分析

针对日益严重的环境污染、锅炉热效率低等问题，阐述了燃煤锅炉炉内空间分级燃烧技术、煤粉浓淡高效分离技术改造项目和特点，提出了对燃烧器系统、一次风管道、二次风系统和空预器系统等系统进行具体的低氮改造措施。分析了300 MW燃煤锅炉低氮改造后的热经济性和安全性。经试验验证，1号锅炉低氮改造后，锅炉NOx 排放量大幅减少，排放浓度降到了280 mg／m3。     

风电场环境影响评价原则及评价重点研究

针对风电场环境影响评价的评价原则及评价重点进行了探讨性的研究。提出了风电场环境影响评价应以早期介入和避让措施优先为基本原则；对风电场环境影响评价重点进行了识别，并提出风电场选址的环境可行性分析是风电场环评的重中之重；风电项目建设对生态环境的影响及风机噪声、光影影响也是风电场环境影响评价的重点，并创造性的提出风机噪声光影联合防护区的概念，以期对风电场环境影响评价提供理论及技术参考依据。     

PW_(12)/g-C_3N_4光催化降解甲基橙

采用浸渍法制备了磷钨酸(PW12)/g-C3N4复合光催化剂,并将其用于溶液中甲基橙的光催化降解,运用IR技术对使用前后的光催化剂进行了表征。表征结果显示,PW12和g-C3N4的结构未在浸渍负载中发生改变,且PW12和g-C3N4结合牢固。实验结果表明:最佳的PW12负载量(光催化剂中PW12的质量分数)为50%;光催化降解甲基橙的优化反应条件为初始甲基橙质量浓度5 mg/L、光催化剂加入量0.6 g/L、初始溶液p H=7;在优化条件下,分别采用紫外光、模拟太阳光、可见光照射120 min后,甲基橙的降解率分别为96.59%,82.23%,42.78%;该光催化剂固载良好,使用中不易发生溶脱,稳定性好,可重复使用。     

Uncertainties in QRA: Analysis of losses of containment from piping and implications on risk prevention and mitigation

Quantitative Risk Assessment (QRA) is commonly used in the chemical industry to support decision-making. Common practices are based on standard methods, such as fault tree, event tree, etc.; in this frame, risk is a function of frequency of events (probability) and associated consequences (negative outcomes), but relevant uncertainties often are not properly taken into account in the derived results. This paper presents the application of an extended risk analysis of loss of containments for a case-study with the following aims: firstly, the uncertainties related to the results of the analysis, which derive from assumption in the application of the standard models, are qualitatively assessed; secondly the application allows evaluating the impact of the uncertainties on the trustworthiness of the results and, finally, commenting about their use in the risk prevention and mitigation.     

生活垃圾焚烧发电厂周边环境二噁英污染水平及人群暴露评估

选取某典型生活垃圾焚烧发电厂为研究对象,监测其周边环境空气、土壤、地下水、农作物等环境介质中二噁英的浓度水平,初步评估周边人群二噁英暴露水平。研究结果表明,该厂周边环境空气、土壤、地下水中二噁英测定值分别为0. 236 pg TEQ/m3～0. 331 pg TEQ/m3、1. 94 ng TEQ/kg～2. 71 ng TEQ/kg、0. 17 pg TEQ/L～0. 26 pg TEQ/L,企业排放的二噁英对周边环境影响较小;成人和儿童在暴露介质中摄入二噁英总量分别为0. 959 pg TEQ/(kg·d)和1. 59 pg TEQ/(kg·d),均低于4 pg TEQ/(kg·d)的标准,经大米和面粉摄入二噁英的量超过总暴露量的90%,提示食物是人群二噁英暴露的主要介质。     

上海城区交通干道黑碳污染调查

采用设置在上海市中心城区交通主干道旁空气质量自动监测站2018年1—12月的观测数据,分析黑碳气溶胶(BC)污染特征及其与PM_(2.5)、SO_2、NO_x、CO、O_3、苯、甲苯、乙苯、二甲苯和气象参数的相关性。结果表明,观测期间内,BC小时均值为(3 038±22) ng/m~3,ρ(BC)在ρ(PM_(2. 5))中占比为(11. 48±0. 12)%。日内ρ(BC)变化呈双峰型,各月份之间ρ(BC)变化不大。ρ(BC)与风速呈负相关,与PM_(2. 5)、NO_x、CO、苯、甲苯、乙苯和二甲苯呈正相关。     

Usage of polystyrene disposable food dishes in the lightweight concrete making

The increasing use and subsequent accumulation of polystyrene containers has triggered a substantial environmental problem. This study investigated using varied percentages of solid waste polystyrene disposable food dishes in the production of lightweight concrete samples with 350 kilograms per cubic meter (kg/m³) of cement and a density of 1,300 kg/m³. The polystyrene disposable dishes were ground into beads of 0–3 millimeters (mm) and 3–6 mm in size. First, the characteristics of Type II Portland cement, polystyrene, and aggregates were examined. The following characteristics of concrete using ASTM International and British Standards Institution standards were tested: slump, compressive strength, ability to resist chloride ion penetration, and resistance of concrete to rapid freezing and thawing cycles. Scanning electron microscopy (SEM) and energy dispersive X‐ray spectroscopy analytical techniques were also used. The slump of samples varied between 40 and 70 mm and was not dependent on either the polystyrene percentage or the size of the polystyrene beads in the concrete samples (p‐value > .05). The compressive strength of the concrete samples after 90 days of curing, and using different percentages of polystyrene, varied between 96 and 113 kilograms per square centimeter (kg/cm²). The resistance of the samples to the freezing and thawing cycle and chloride ion penetration were affected unfavorably by the presence of the polystyrene. The SEM technique indicated that concrete samples containing 15% and 25% polystyrene had denser crystals and less void than concrete samples with 40% and 55% polystyrene.     

Review: recent advances in biogas purifying technologies

Biomethane production through biogas upgrading is a promising renewable energy for some industries which could be part of the equilibrium needed with fossil fuels consumption to achieve a sustainable society. This paper presents a comprehensive list of biogas upgrading technologies focused on carbon dioxide removal as well as recent advances reported by researcher with wide expertise in this topic. Additionally, an extensive costs–performance comparison among the technologies studied is discussed. Among the different alternatives, chemical scrubbing stood out to achieve high biomethane purities while cryogenic technologies proved to be effective against methane losses. Regarding the different costs, water scrubbing and membrane separation seem to be the most affordable techniques.     

Research on flow assurance of deepwater submarine natural gas pipelines: Hydrate prediction and prevention

The formation of hydrate will lead to serious flow assurance problems in deepwater submarine natural gas transmission pipelines. However, the accurate evaluation model of the hydrate blocking risk for submarine natural gas transportation is still lacking. In this work, a novel model is established for evaluating the hydrate risk in deepwater submarine gas pipelines. Based on hydrate growth-deposition mechanism, the mathematical model mainly consists of mass, momentum and energy conservation equations. Meantime, the model results are obtained by finite difference method and iterative technique. Finally, the model has been applied in the production of deepwater gas field (L Gas Field) in China, and the sensitivity analysis of relevant parameters has been carried out. The results show that: (a). The mathematical model can well predict the hydrate blockage risk in deepwater natural gas pipelines after verification. (b). Hydrate is easily formed at the intersection of horizontal pipeline and vertical riser, and the maximum blocking position often occurs in middle of the riser. (c). The hydrate blockage degree and length of hydrate formation region (HFR) decrease with the increase of gas transport rate. (d). The hydrate blockage degree and length of HFR decrease with the increase of gas transport temperature. (e). The hydrate blockage degree and length of HFR increase with the extension of horizontal pipeline. (f). Injecting inhibitors can effectively inhibit hydrate formation and blockage, but the improvement of transmission measures can significantly reduce the dosage of inhibitor. It is concluded that measures such as increasing gas transportation rate and temperature, shortening horizontal pipeline length, optimizing inhibitor injection point and injection rate can play a safe, economic and efficient role in hydrate preventing and controlling.